Filler Metal F Number

ASME Boiler and pressure vessel code (BPVC) has assigned certain numbers to base metals as well as to filler metals (electrodes).

Filler Metal F-number 6
Aws Filler Metal Chart

ERNiCrMo-3 is used for Gas Metal Arc Welding (GMAW) and Gas Tungsten Arc Welding (GTAW) of Inconel 601, Inconel 625, Incoloy 825 and a range of high alloy austenitic and super austenitic stainless steels. Dissimilar welding applications includes joining Inconel alloys, Incoloy alloys, low-alloy steels, stainless steels and carbon steels. Prolonged temperatures in excess of 1500 f. Special alloys and tempers are often required to overcome this problem. Contact alcotec for assistance in alloy and temper selection when elevated temperature service is a concern. Alcotec wire corporation 2750 aero park dr., traverse city, mi u.s.a. 1-800-228-0750 fax 231-941-9154.

For base metals, ASME has assigned two number system, these are;

P Numbers
Group Numbers

For filler metals, the number system which is assigned, are as follows;

F Number
A Number

These numbers can be found in ASME BPVC Section IX, please see Table–1 for details;

Table – 1

BASE METAL GROUPING:

The main purpose of assigning this number system is to reduce the number of procedure qualification records (PQR). Conducting a procedure qualification requires a lot of time and money due to the following procedural requirements;

Preparation of test coupon
welding of test coupon and
sending it to a lab for destructive test

Hence, to reduce these costly and time-consuming activities, ASME has done grouping of base metals and has assigned certain P numbers to each group of metals. This grouping of base metals has been done on the basis of the following parameters;

Material composition
Weldability
Mechanical property

Though all materials of the same ‘P’ number doesn’t exhibit the same properties, but after considering the above-mentioned parameters, ASME has done this logical grouping.

Why this grouping is required?

Suppose, if we change the base metal from an existing qualified WPS and if the new base metal falls in the same ‘P’ number then the requalification of the existing WPS is not required, it means no need for a new PQR.

But this doesn’t mean that one can easily substitute the base material, from existing WPS, of same ‘P’ number at any time. Whenever there is a change in the base material from existing WPS, the compatibility shall be considered with regards to the following factors;

Metallurgical property
Mechanical property
Design considerations
Service requirements
Heat treatment

Table–2 shows the assignment groups for various metals and their alloys (according to ASME BPVC).

Table – 2

Now that we have understood ‘P’ numbers let’s move on to group numbers. Group numbers are subsets of ‘P’ numbers assigned to ferrous based metals. Group numbers are assigned only to those materials which require toughness testing for the qualification of its WPS.

We will take an example of SA516 Gr 65 from table QW/QB-422 (Page – 118 of ASME Section IX, 2017 edition), we can find out the following values;

Base material – SA516 Gr 65

Tensile strength (min.) – 65 Ksi (or 450 Mpa)
P-No. – 1
Group number – 1
Nominal composition – C-Mn-Si
Typical product form – Plate

Another grouping of base metals was the ‘S’ numbers, but the ‘S’ number is not used nowadays. It was deleted from ASME in 2009.

S Numbers were assigned to those materials which were acceptable for use by the ASME B31 Code for Pressure Piping, or by selected Boiler and Pressure Vessel Code Cases, but were not included in section II of ASME Boiler and Pressure Vessel (BPVC). Base metals that were previously assigned ‘S’ Numbers were reassigned the corresponding P Numbers or P Numbers and Group Numbers.

FILLER METAL (ELECTRODE/WELDING ROD) GROUPING:

The F Number: F number grouping (for filler metals) is done to reduce the number of welding procedure specifications (WPS) and welder performance qualifications. The basis for F number grouping is usability characteristics. The usability characteristics fundamentally determine the ability of a welder to produce sound welds with a given filler metal. Hence it is assumed if a welder can make satisfactory weld with a particular filler metal, he will be able to weld with all the filler metals belonging to that particular ‘F’ number.

Table-3 shows a brief summary of ‘F’ and filler metals (according to ASME BPVC, Table: QW-432).

Table – 3

The ‘F’ number grouping doesn’t imply that one can easily substitute the filler metal (electrode/welding rod), from existing WPS, of the same ‘F’ number at any time. Whenever there is a change in the filler metal (electrode/welding rod) from existing WPS, the compatibility shall be considered with regards to the following factors;

Metallurgical property
Mechanical property
Design considerations
Service requirements
Heat treatment

The A Number: Another type of grouping for filler metal or welding rod is the ‘A’ Number. ‘A’ number grouping has been done on the basis of the chemical composition of the deposited weld metal. This can be found in ASME BPVC Section IX, Table – QW-442).

Please watch the video (given below) for more clarity on this topic;

Also read: Thickness range for welder qualification

Filler Metal F-number 6

Aws Filler Metal Chart

Also read: Welding Electrodes/Filler metal